Welcome Guest to Charlie's FlyBox!
X-Caddis
step: 1
Pattern Description
The X-Caddis comes from Yellowstone fishing guru Craig Matthews. Craig is the guy who brought us the Sparkle Dun and a host of other effective patterns, trademarked by their simplicity. The X-Caddis is no exception, and can be whipped out by the dozenz! I like the X-Caddis in smaller sizes, from 18-24, although it certainly holds it's own in bigger sizes as well. It imitates a caddis with the shuck still attached, but I think it's general profile can match many different isects in various stages of emergence..in other words, it just looks like food! Tie some up and see what you think.
Materials Needed: All materials used here available for mail order. Please use the contact form for pricing and details.

Hook: TMC 100 #14-24............................ Thread: 8/0 Olive..................................... Shuck: Brown Zelon................................. Body: Olive Superfine or Antron Dubbing.......... Wing: Natural Deer Hair
step: 2  
Start the tying thread about an eye length back from the hook eye and build a smooth thread base back to the bend. Return the thread to the starting point.
X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis
click to enlarge
step: 3  
Tie in a small clump (about half a strand for a #16) of Zelon for the shuck just behind the eye of the hook.
X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis
click to enlarge
step: 4  
Wrap back over the Zelon to the bend of the hook and return the thread once again to the starting point.
X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis
click to enlarge
step: 5  
Dub the body from the bend of the hook up to just behind the eye with a slight taper.
X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis
click to enlarge
step: 6  
Cut, clean and stack a small clump of deer hair. Measure the hair against the hook shank so it matches the length of the hook. You can also tie the X-Caddis with a shorter wing to imitate partially emerged cripples and I do that as well on some flies.
X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis
click to enlarge
step: 7  
Cut the clump of deer hair to the length of the hook and hold it in place with the butt ends of the hair just behind the eye of the hook.
X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis
click to enlarge
step: 8  
Place two loose turns of thread over the hair just behind the hook eye.
X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis
click to enlarge
step: 9  
Pull the thread TOWARD YOU to tighten it while holding the long tip ends of the hair in place on top of the hook.
X-Caddis X-Caddis X-Caddis X-Caddis X-Caddis
click to enlarge
step: 10  
Wrap the thread forward with two turns through the butt ends of the hair right up to the hook eye. The thread goes through the butt ends of the hair binding them down along the way, securing them tightly in place.
X-Caddis X-Caddis X-Caddis X-Caddis
click to enlarge
step: 11  
Clip the thread and then trim the Zelon shuck to about a shank length long.
X-Caddis X-Caddis X-Caddis
click to enlarge
step: 12  
Finished Fly, Side View
X-Caddis X-Caddis
click to enlarge
step: 13  
Finished Fly, Bottom View
X-Caddis
click to enlarge