charlie's flybox

Gurgler


Fly Patterns brought to you by Charlie's FlyBox
© All images, slogans and content are strictly copyrighted and may not be used or copied
without permission.
Charlie Craven and Charlie's FlyBox, Inc.
print this page

step: 1
Pattern Description
The Gurgler, or, more correctly, the *Gartside* Gurgler was developed my angling ranconteur, Jack Gartside. A simple top water pattern at home in front of everything from bluefish to bass, the Gurgler is a fly that even a novice can tie. While not really a "popper" or a "slider", the Gurgler has a unique action that *gurgles* and sputters along the surface, drawing attention and strikes from a variety of game fish. While the pattern I'll present here is tied on a saltwater hook, there are a variety of fresh water hooks appropriate as well for warm water fishing. Get on it...this one is easy...
Materials Needed:

Hook: TMC 811S #1/0-6>>>>> Thread: 140-280 Denier UTC thread, in this case red, but to your liking>>>>> Tail: White Bucktail>>>>> Flash: Pearl Krystal Flash>>>>> Shellback: White Open Cell Foam, 1/4 inch thickness>>>>> Hackle: Grizzly Neck Hackle>>>>> Body: Pearl Tinsel Chenille>>>>
step: 2
Place the hook in the vise and dress the shank with a layer of thread from the hook eye to the bend and back again. Coat the thread wraps with a light coat of head cement. charlie's flybox
charlies flybox
step: 3
Cut and clean a small clump of bucktail. Even the tips by pulling out the shortand the long fibers but do not stack it...we want this a little tapered and ragged on the ends. Measure the clump against the hook so the tips extend beyond the hook bend about two shank lengths with the butt ends just behind the hook eye. charlie's flybox
charlies flybox
step: 4
Cut the butt ends of the bucktail square and tie them in with several tight wraps of thread about two eye lengths back from the hook eye. I like to spin my bobbin up to twist the thread a bit before doing this so the thread will cut in and grab the hair tightly. charlie's flybox
charlies flybox
step: 5
Lift up the long ends of the hair to keep them on top of the hook as you spiral wrap the thread tightly back over them to the bend. charlie's flybox
charlies flybox
step: 6
Ought to have something that looks about like this right now. charlie's flybox
charlies flybox
step: 7
Tie in three or four strands of pearl krystal flash at the center of its length at the base of the tail. Fold the front ends back over the tail and trim the ends to random lengths about evenish with the end of the tail. LEave some long, some shorter and some in between so they don't look like a paintbrush...or cut them all square, I don't care, I'm not your mother! charlie's flybox
charlies flybox
step: 8
Mom says like this... charlie's flybox
charlies flybox
step: 9
Wrap forward over the butt ends, covering them tightly with thread. Coat the wraps with head cement. charlie's flybox
charlies flybox
step: 10
Cut a strip of 1/4" foam to just slightly narrower than the hook gap. charlie's flybox
charlies flybox
step: 11
Fold the end of the foam around the hook so it cups to the shank about three eye lengths back from the hook eye. charlie's flybox
charlies flybox
step: 12
Make a single turn of thread over the foam, but don't tighten it until you come all the way around and pull straight down. Hold the foam in place on the top of the hook as you do this then follow up with a couple more tight wraps stacked on top of the first. charlie's flybox
charlies flybox
step: 13
Spiral wrap the thread back over the foam to the bend, anchoring it with a band of thread when you get there. charlie's flybox
charlies flybox
step: 14
Select a large grizzly neck feather and preen the fibers so they stand out away from the stem. charlie's flybox
charlies flybox
step: 15
Peel the fibers off the inside of the feather...that is, the side that will touch the hook when you wrap it around the shank. We'll be tying this feather in by its tip so that ought to help you visualize which side to strip. charlie's flybox
charlies flybox
step: 16
Tie the grizzly feather in by its tip at the bend of the hook and clip the excess tip after anchoring it flush. charlie's flybox
charlies flybox
step: 17
Tie in a length of pearl krystal chenille at the bend of the hook with a few tight turns of thread. charlie's flybox
charlies flybox
step: 18
Return the thread to just in front of the foam behind the eye. charlie's flybox
charlies flybox
step: 19
Wrap the chenille forward and tie it off at the front of the faom strip. Clip the excess. charlie's flybox
charlies flybox
step: 20
Build a smooth thread base behind the hook eye. charlie's flybox
charlies flybox
step: 21
Wrap the hackle forward in an open spiral to the front of the chenille body and tie off. Clip the excess and wrap firmly over the stub end. charlie's flybox
charlies flybox
step: 22
Preen the hackle fibers down from the top to each side and.... charlie's flybox
charlies flybox
step: 23
Pull the foam forward over the top of the shank, slightly cupping it around the body. charlie's flybox
charlies flybox
step: 24
Unwind the bobbin to make sure the thread is flat and make a single turn over the top of the foam. While pinching the long end of the foam just behind the hook eye, tighten the thread wrap by pulling firmly and steadily down. Make two more wraps on top of this wrap to anchor the foam. charlie's flybox
charlies flybox
step: 25
Lift the front end of the foam and build up the thread head a bit, pushing the foam slightly upward. charlie's flybox
charlies flybox
step: 26
Clip the front end of the foam straight across, leaving a bit oflength to form the gurgling lip. charlie's flybox
charlies flybox
step: 27
Bring the thread back into the notch and whip finish. charlie's flybox
charlies flybox
step: 28
Finished fly, side view. charlie's flybox
charlies flybox
step: 29
Top quarter view... charlie's flybox
charlies flybox
step: 30
Front view... charlie's flybox
charlies flybox