charlie's flybox

Zonker


Fly Patterns brought to you by Charlie's FlyBox
© All images, slogans and content are strictly copyrighted and may not be used or copied
without permission.
Charlie Craven and Charlie's FlyBox, Inc.
print this page

step: 1
Pattern Description
The Zonker is a unique baitfish pattern developed by Dan Byford. The beauty of the Zonker lies in it's simplicity. It can be tied with as few as two materials, but we have dressed it up a bit here and added a few parts. The Zonker was the first fly that made use of stripped rabbit hide, and as a result the material itself has taken off in popularity since then. I am always looking for new pattern looks to add to my box and the Zonker certainly has an unusual look and an inherent fishiness to it. The rabbit strip wing flows and swims through the water, while the mylar belly adds flash and proflie to the fly. I like Zonkers in stillwaters, where fish get a longer look at the fly and therefore need a more realistic pattern to turn the key, as well on on moving water where I will fish it behing a larger, bulkier pattern.
Materials Needed:

Hook: TMC 300 #2-10 Thread: White 3/0 Monocord Weight/Keel: .035 lead wire Body: Large Mylar Tubing, color of choice Wing: Stripped Rabbit Hide (Zonker Strip) Eyes: Adhesive Eyes in Color to match or contrast body
step: 2
Place the hook in the vise and pinch the barb flat. Wrap a thread base back to just behind the hook point. charlie's flybox
charlies flybox
step: 3
Attach a five-inch length of lead wire to the top of the hook shank with the long end pointing out over the hook eye. Bind the lead to the shank with tight spiraling wraps from just in front of the hook point to about four eye lengths back from the hook eye. This can be a little tricky with the long end of the lead sticking out in your way, so just bend the lead into a coil to get it out of the way while you wrap the thread. charlie's flybox
charlies flybox
step: 4
End with the thread hanging at the bend of the hook. charlie's flybox
charlies flybox
step: 5
Loop the wire back toward the bend of the hook as shown. This wire will form the frame around which the mylar will form the body. charlie's flybox
charlies flybox
step: 6
Clip the wire where the end lines up with the bend of the hook. make this cut at an angle so there is a smooth trasition from the wire to the hook shank. The size of the wire loop will determine the ultimate body shape of the finished fly and you want to have a little bit larger loop than you think you'll need to fill out the tubing. charlie's flybox
charlies flybox
step: 7
Bind the end of the wire down above the hook point forming a smooth transition from the wire to the hook shank. charlie's flybox
charlies flybox
step: 8
Apply a coat of head cement to the thread wraps biding the wire down to the shank as well as to the tie down area at the rear of the hook. charlie's flybox
charlies flybox
step: 9
Cut a length of mylar tubing so it is about half again linger than the shank of the hook. Pull the cord out of the center of the tubing and crease the tubing by running it along the closed blades of you scissors to form a flattened sheet. Push the tubing over the hook eye and continue over the wire body frame. The frame will open the tubing up and create the deep belly of the finished fly. charlie's flybox
charlies flybox
step: 10
Push the tubing back to the bend of the hook. Fray the back end of the tubing slightly to allow the thread to slip through the ends. charlie's flybox
charlies flybox
step: 11
With the thread well inside the end of the tubing, pinch the tubing and execute a pinch wrap to bind the back end of the tubing to the shank. Try to get a clean tie down here at the bend and make sure the thread wraps are tight. charlie's flybox
charlies flybox
step: 12
Clip the excess butt ends of the mylar flush against the hook shank and build a smooth tapered thread base over the butts. charlie's flybox
charlies flybox
step: 13
Tie a whip finish at the bend of the hook using either your fingers or an extended reach whip finish tool. Clip the thread. charlie's flybox
charlies flybox
step: 14
Pull the tubing tight at the front end of the fly so the mylar hugs the form made by the wire frame. Pinch the tubing against the hook shank and re-start the thread right over the top of the tubing. Bind the tubing down tightly at the front of the wire frame. charlie's flybox
charlies flybox
step: 15
Clip the butt end of the thread and the tips of the excess mylar tubing as close to the hook as you can. Build a small thread base over the stubs and end with the thread at the very front edge of the mylar body. You should have about two eye lengths worth of bare space between the eye and the front of the body. charlie's flybox
charlies flybox
step: 16
Invert the hook in the vise and position the wire frame so it opens up the mylar tubing to form the belly of the fly. Just push and pull on the wire to get the shape you want. charlie's flybox
charlies flybox
step: 17
Poke the hook point through a Zonker strip from the hide side. The strip should extend well beyond the eye of the hook to the front and well past the bend at the rear. Remove the hook from the vise and position the strip flush against the thread tie down area at the back of the body. Replace the hook in the vise. charlie's flybox
charlies flybox
step: 18
Pull the Zonker strip taut up to the eye of the hook and bind it down at the front of the body. Don't worry about the length off the back of the hook for right now. charlie's flybox
charlies flybox
step: 19
Cut the excess Zonker strip off flush against the hook shank. charlie's flybox
charlies flybox
step: 20
Build a smooth thread head to cover the stub of the Zonker strip and whip finish the thread. Clip the thread. charlie's flybox
charlies flybox
step: 21
Clip the strip beyond the bend of the hook so it is about half a shank length long. If you leave it much longer, it will foul around the hook point, so keep it a little on the short side. When you cut the strip, part the hair and cut only the hide, leaving the hair to form the tapered tail. charlie's flybox
charlies flybox
step: 22
Place a drop of Zap-A-Gap on either side of the front of the fly where the eyes will go. I like to overlap the eyes onto the fur strip slightly. I also place the eyes on the front of the body as this is where a real fishes eyes are, not up on the thread head. charlie's flybox
charlies flybox
step: 23
Press an adhesive eye against the glue spot on both sides of the fly and press them together for a few seconds. The glue will penetrate through the Mylar body and glue the backsides of the eyes to each other. Let the glue dry for a few minutes and apply a thin coat of head cement to the thread head. charlie's flybox
charlies flybox
step: 24
Finished Fly, Side View. Note the length and taper of the rabbit strip tail. This fly has a larger belly and longer rabbit strip wing. You can use a shallower beely shape and shorter fur strip to create a more streamlined minnow shape too. charlie's flybox
charlies flybox
step: 25
You can also use a marker to barr the wing as in the top fly here. This will create more of a perch like coloration on the fly. The bottom fly shown here has a more slender body as well. Play with the loop shape on the lead wire frame to get different looks. charlie's flybox
charlies flybox